In Stock
The mixer test lead can be connected to electromagnetic injectors, primary circuit or control signal of individual ignition coils. It allows you to record a signal from up to six sources at the same time, using only one analog input of the oscilloscope.
| Manufacturer | ROTKEE (Ukraine) |
| Maximum number of signal sources | 6 |
| Operating voltage | 60 V maximum |
| Removable lead connector | 4 mm “banana” |
| Output connector | BNC |
| Total length | 2.5 m |
| Operating temperature range | -20 to 80 ℃ |
| Weight | 260 g |
Recording and analyzing the injectors’ signals of Subaru Impreza 2010 2.0 EJ204 using TL-mix6 mixer test lead and MT Pro automotive oscilloscope. Wiring diagram, test probe connection, oscilloscope setup, waveform record procedure on idling and wide-open throttle.
The mixer test lead is specially designed for making measurements in internal combustion engines and allows you to work comfortably with in-line, V-shaped and opposing engines. A soft microphone cable with a dense braided shield is used as a cord. 4 mm "Banana" plugs are used as test lead connectors; BNC is a sensor-oscilloscope connector.
The replacement leads are made of a flexible PVC cable. A flexible lead pin is ideal for connecting an oscilloscope to automotive connectors as well as other recessed areas. A thin pin and a handy holder allow connecting to virtually any connector without damaging the circuit and wiring insulation, which enables to reduce the circuit rust. The spring prevents the pin from accidental breakage.
With the help of a standard 4 mm Banana plug you can easily connect/disconnect/change test leads. This plug is compatible with test leads from other manufacturers as well as multimeters. If needed, the test lead pin can be replaced by an alligator clip or a plunger mini hook.
Using 6 test leads allows you to make measurements on 6 ignition coils or injectors at a time, and therefore you can analyze the signals directly from all the cylinders of the engine. The pulses of ignition coil control as well as the injector control pulses from different cylinders never occur at the same time, which allows summing signals from all the test leads in order to get one signal at the output with a series of sequential pulses identifying the ignition system as a whole.
NB! The test lead doesn’t have a separate grounding terminal; therefore, an additional grounding wire of the oscilloscope is required.
When designing the test lead, high emphasis has been placed on a signal cables joint as this junction is damage-prone. Each of these joints includes a circuit board with the test lead’s electronic components. The board not only supports the loads, but also fixes the cable. Such solid joints prevent cable breakdown and increase its durability.
The test lead is compatible with the MT Pro oscilloscope as well as any other oscilloscope. It can be connected to any analog channel.
injector control signal waveform
individual ignition system primary voltage waveform
The mixer test lead can be connected to electromagnetic injectors, primary circuit or control signal of individual ignition coils. It allows you to record a signal from up to four sources at the same time, using only one analog input of the oscilloscope.
Designed for connecting an oscilloscope to automotive connectors without having to use a break out box or damage the wire isolation as well as other recessed areas. Compatible with TL-mlp, TL-light, TL-light, TL-dif, TL-mix4, TL-mix6 test leads.
Designed for connecting an oscilloscope to automotive terminals and wires, both thin and thick wires of up to 15 mm diameter. Compatible with TL-mlp, TL-light, TL-light, TL-dif, TL-mix4, TL-mix6 test leads.
The multipurpose test lead is an essential part of an automotive oscilloscope. It allows you to evaluate output voltage and catch waveforms in car connectors, terminals and other circuits.
Designed for connecting an oscilloscope to automotive connectors and other recessed areas without damaging wire isolation. The leads are 2 metres long, which allows tracing wires easily. Compatible with TL-mlp, TL-light, TL-light, TL-dif, TL-mix4, TL-mix6 test leads.